Kontron AT8050 Manuel d'utilisateur Page 124
- Page / 165
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Software Setup
108 AT8050
www.kontron.com
5.1.7.8 VLAN Priority Configuration
5.1.7.9 Watchdog Timer sub-menu
Feature Option Description Help text
LAN Parameter Selector 21
The parameter selector assignments are
described in IPMI Specification 2.0, table 23-
4. Selector #21: 802.1q VLAN Priority.
N/A, display only.
Channel Number 01 or 02
Each interface has a channel number that is
used when configuring the channel and for
routing messages between channels. Channels
01 and 02 on Base interface are available. The
channel number assignments are described in
IPMI Specification 2.0, table 6-1.
Enter Channel Number
for SET LAN Config
Command. Proper value
01 or 02.
Channel Status: Valid or Invalid Display Valid if IPMC support LAN Channel. N/A, display only.
802.1q VLAN Priority
Value
x
This allows setting an 802.1q VLAN priority for
LAN configuration.
Enter VLAN Priority
value in decimal. Proper
value below 8.
Current VLAN Priority
Value:
x
Display the current 801.1q VLAN Priority
configuration stored in IPMI NVRAM for IPMI
LAN.
N/A, display only.
Feature Option Description Help text
BIOS POST Timeout
Disabled
60
120
150
300
600
Configures the BIOS POST IPMI HW watchdog
timeout value in seconds. The BIOS POST
watchdog will be disabled if the timeout value
is set 0.
Select the BIOS POST
IPMI HW watchdog
timeout value.
BIOS POST Action
No Action
Warm Reset
Power Down
Power Cycle
Configures which action to take when the BIOS
POST IPMI HW watchdog expires. Note: warm
reset is done only if a complete cold boot POST
sequence has been successfully completed. If
the warm reset flag at address 40:72h is not
set, BIOS will force a cold reset.
Select which action to
take when the BIOS POST
IPMI HW watchdog
expires.
OS Load Timeout
Disabled
15
30
45
60
90
120
150
300
600
Configures the OS Load IPMI HW watchdog
timeout value in seconds. The OS Load
watchdog will be disabled if the timeout value
is set 0.
Select the OS Load IPMI
HW watchdog timeout
value.
OS Load Action
No Action
Warm Reset
Power Down
Power Cycle
Configures which action to take when the OS
Load IPMI HW watchdog expires.
Select which action to
take when the OS Load
IPMI HW watchdog
expires.
- » Kontron User's Guide « 1
- Revision History 2
- Customer Service 2
- Table of Contents 3
- List of Figures 7
- List of Tables 8
- Safety Instructions 10
- How to Use This Guide 12
- Customer Comments 13
- Advisory Conventions 13
- Unpacking 14
- Powering Up the System 14
- Adapter Cables 14
- Storing Boards 14
- Safety Certification 15
- CE Certification 15
- Limited Warranty 16
- Product Description 17
- 1. Product Description 18
- 1.3 Board Specifications 19
- * Designed to meet or exceed 20
- 1.4 Compliance 21
- 1.5 Hot-Plug Capability 21
- 1.6.1.2 Serial Port Feature 22
- 1.6.1.3 Hot Swap 22
- 1.6.2 Advanced Mezzanine Card 23
- Board Features 24
- 2. Board Features 25
- 2.2 System Core 26
- 2.3 USB 2.0 Interfaces 27
- 2.4 USB Flash Module 28
- 2.6 Update Channel 29
- 2.8 Redundant BIOS Flash 29
- 2.9 Ethernet Interfaces 30
- 2.9.2 Base Interface 31
- 2.9.3 Management Interface 31
- AMC 32
- BIOS Settings: 33
- Configuration 36
- 2.10 Serial Interfaces 40
- 2.11 AMC Mezzanine 40
- 25 AT8050 41
- 2.12 FPGA 42
- 2.13 Telecom Clock Option 42
- 2.15 LEDs Description 43
- Figure 2-10: Faceplate LEDs 44
- Installing the Board 45
- 3. Installing the Board 46
- 3.2 Processor 47
- 3.3 Memory 47
- 32 AT8050 48
- 3.3.2 Installing Memory 49
- }Channel 2 50
- }Channel 1 50
- }Channel 0 50
- 3.5.2 Removing the Board 51
- 3.5.3 Installing an AMC 52
- 3.5.4 Removing an AMC 52
- 3.5.5 Installing the RTM8050 52
- 3.5.6 Removing the RTM8050 52
- Hardware Management 53
- 4. Hardware Management 54
- 4.2.2 Sensors 55
- 4.3 IPMC 56
- 41 AT8050 57
- 42 AT8050 58
- 43 AT8050 59
- 44 AT8050 60
- 45 AT8050 61
- Table 4-13:SOL Commands 62
- 47 AT8050 63
- 4.3.2 Sensor Data Records 64
- 4.3.2.1 IPMC Sensors 65
- 50 AT8050 66
- 51 AT8050 67
- 52 AT8050 68
- 53 AT8050 69
- 54 AT8050 70
- 55 AT8050 71
- 56 AT8050 72
- 57 AT8050 73
- 4.3.3 FRU Information 74
- 59 AT8050 75
- 60 AT8050 76
- 61 AT8050 77
- 62 AT8050 78
- 63 AT8050 79
- 64 AT8050 80
- 65 AT8050 81
- Carrier Device 0) 82
- Carrier Device 1) 83
- 68 AT8050 84
- 69 AT8050 85
- 70 AT8050 86
- 71 AT8050 87
- 72 AT8050 88
- 73 AT8050 89
- 74 AT8050 90
- 75 AT8050 91
- 76 AT8050 92
- 77 AT8050 93
- 78 AT8050 94
- 79 AT8050 95
- 80 AT8050 96
- 81 AT8050 97
- 82 AT8050 98
- 5. Software Setup 100
- Software Setup 101
- 85 AT8050 101
- 5.1.2 Menu Bar 102
- 5.1.3 Main Menu 103
- 5.1.4 Advanced Menu 104
- 89 AT8050 105
- 90 AT8050 106
- 91 AT8050 107
- 92 AT8050 108
- 93 AT8050 109
- 94 AT8050 110
- 95 AT8050 111
- 96 AT8050 112
- 97 AT8050 113
- 5.1.5 Security Menu 114
- 5.1.6 Boot Menu 115
- 100 AT8050 116
- 101 AT8050 117
- 102 AT8050 118
- 103 AT8050 119
- 5.1.7 System Management Menu 120
- 105 AT8050 121
- 106 AT8050 122
- 107 AT8050 123
- 108 AT8050 124
- 109 AT8050 125
- 110 AT8050 126
- 111 AT8050 127
- 112 AT8050 128
- 5.2 Boot Utilities 129
- 5.2.4 BOOT Menu POP-UP 130
- 5.3.1 Requirements 130
- 115 AT8050 131
- Thermal Considerations 132
- 6. Thermal Considerations 133
- 118 AT8050 134
- 6.1.3 Airflow blockers 135
- 6.1.4 System Airflow 135
- 6.1.5 Thermal Profile 136
- A. Memory & I/O Maps 137
- A.2 Kontron I/O Mapping 138
- A-3 AT8050 139
- A-4 AT8050 140
- A.4 Telco Clock 141
- A.4.1 Register Description 142
- A-7 AT8050 143
- A-8 AT8050 144
- A-9 AT8050 145
- A-10 AT8050 146
- B. Connector Pinouts 147
- B.3 AMC B1(J5) 148
- B.4 Ethernet(J8 & J9) 149
- B.5 USB Port (J10) 149
- B.6 Serial Port, COM1(J12) 149
- B.8 USB Flash Drive(J22) 150
- B-5 AT8050 151
- B.10 RTM Connector (J30) 152
- B.11 Power (P10) 153
- C. BIOS Setup Error Codes 154
- C.2 POST Code Checkpoints 155
- C-3 AT8050 156
- C.3 DIM Code Checkpoints 157
- C-5 AT8050 158
- D. Software Update 159
- E. Getting Help 160
- E.2 When Returning a Unit 161
- F. Glossary 162
- F-2 AT8050 163
- F-3 AT8050 164
- F-4 AT8050 165
Produits connexes et manuels pour Matériel Kontron AT8050
Matériel Kontron AT8242 Manuel d'utilisateur
(109 pages)
(109 pages)
Matériel Kontron AT8060 Manuel d'utilisateur
(160 pages)
(160 pages)
Matériel Kontron KTQ67-FLEX Manuel d'utilisateur
(137 pages)
(137 pages)
Matériel Kontron KTQ77-FLEX Manuel d'utilisateur
(141 pages)
(141 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.196 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels