Kontron NSN2U IP Network Server Manuel d'utilisateur Page 52
- Page / 103
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
51
1. Remove the front chassis cover. For instructions, see “Removing the Front Cover” in
Section 3.2.
2. Remove the front panel bezel from the chassis to access the optical device slot.
3. Loosen the shipping screw that fastens the filler panel to the chassis and remove
the filler panel. (Figure 42, “A”)
NOTE: Keep the filler panel for use later if the optical drive is removed from the
server. The filler panel is required for EMC if there is no optical drive
installed.
Figure 42. Removing the Optical Drive Filler Panel
4. Align the pins in the blue plastic retention mechanism that comes with the kit to
the corresponding holes in the optical drive. (Figure 43)
Figure 43. Attaching the Retention Mechanism to the Optical Drive
5. Holding the drive and the retention mechanism together, slide the optical drive
into the drive opening on the front of the chassis and push until the drive is
seated against the back wall of the drive bracket . (Figure 44, “A”)
- Document Revision 1.2 1
- » Table of Contents « 2
- 1 Introduction 7
- 1.4 Product Accessories 8
- 2 Features 10
- Table 1NSN2U Server Features 11
- 2.1 Server Components 12
- 2.3 NSN2U Server Back Panel 15
- 2.4 Front Panel Board 15
- 2.5 LED/Switch Board 16
- 2.6 Hard Disk Drives 16
- 2.7 Optical Drive 16
- 2.9 Riser Card Assembly 17
- 2.10 Ethernet NIC Ports 18
- 2.12 Power Supply Subsystem 19
- 2.13 System Cooling 19
- Processors 20
- Upgrades 21
- Removing the Back Cover 22
- Re-Installing the Back Cover 22
- Removing the Front Bezel 23
- Installation Procedures 26
- Memory RAS 27
- Channel Independent Mode 28
- Channel Mirroring Mode 28
- Memory Upgrade Rules 29
- Installing Memory DIMMs 30
- Removing a Processor 33
- Installing a New Processor 34
- Inserting the Heat Sink 35
- Procedures 38
- Unit (IBBU) 45
- Connecting the Power Cord 55
- Equipment Rack Precautions 55
- 5.1 Before You Begin 57
- 5.2 Replacing Fans 57
- Replacing 80mm CPU Fans 58
- Replacing 60mm PCI Fans 58
- Removing the Bridge Board 59
- 6 Server Utilities 72
- 6.2 Upgrading the BIOS 74
- 6.4 Clearing the Password 75
- 7 Troubleshooting 77
- Power Light does not Light 79
- 7.5 LED Information 82
- BIOS POST Beep Codes 84
- 8 Warranty 86
- 9.1 Emissions Disclaimer 87
- 9.2 Intended Uses 87
- Temperature and Ventilation 88
- 9.3 Safety Cautions 89
- Wichtige Sicherheitshinweise 90
- Consignes de sécurité 92
- Certification Information 99
- FCC (USA) 100
- Industry Canada (ICES-003) 100
- VCCI (Japan) 101
- BSMI (Taiwan) 101
- 11 Appendix C: Getting Help 102
Produits connexes et manuels pour Matériel informatique Kontron NSN2U IP Network Server
(104 pages)
(49 pages)Panasonic KX-TG9471 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Anrufbeantworter Panasonic KX-TG9471.
Wir stellen 1 PDF-Handbücher Panasonic KX-TG9471 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Commentaires sur ces manuels