Kontron AT8404 CLI Manuel d'utilisateur Page 145
- Page / 373
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
AT8404 Switching Commands
Page 2 - 109 AT8404 CLI Reference Manual
2.21.2.1 no set mld querier query_interval
Use this command to set the MLD Querier Query Interval time to its default value.
2.21.3 set mld querier timer expiry
Use this command to set the MLD Querier timer expiration period. It is the time period that the switch remains in
Non-Querier mode once it has discovered that there is a Multicast Querier in the network.
2.21.3.1 no set mld querier timer expiry
Use this command to set the MLD Querier timer expiration period to its default value.
2.21.4 set mld querier election participate
Use this command to enable the Snooping Querier to participate in the Querier Election process when it discovers
the presence of another Querier in the VLAN. When this mode is enabled, if the Snooping Querier finds that the
other Querier’s source address is better (less) than the Snooping Querier’s address, it stops sending periodic
queries. If the Snooping Querier wins the election, then it will continue sending periodic queries.
2.21.4.1 no set mld querier election participate
Use this command to set the snooping querier not to participate in querier election but go into a non-querier mode
as soon as it discovers the presence of another querier in the same VLAN.
Default disabled
Format set mld querier query_interval <1-18000>
Mode Global Config
Format no set mld querier query_interval
Mode Global Config
Default 60 seconds
Format set mld querier timer expiry <60-300>
Mode Global Config
Format no set mld querier timer expiry
Mode Global Config
Default disabled
Format set mld querier election participate
Mode VLAN Config
Format no set mld querier election participate
Mode VLAN Config
- AT8404 CLI Reference Manual 1
- AdvancedTCA 1
- Revision History 2
- Disclaimer 2
- AT8404 Preface 3
- About This Book 3
- Proprietary Note 3
- Trademarks 3
- Preface AT8404 4
- Explanation of Symbols 4
- For Your Safety 4
- Two Year Warranty 5
- Appendix 25
- 1.1 Command Syntax 28
- 1.2 Command Conventions 28
- 1.3 Common Parameter Values 29
- 1.6 FASTPATH Modules 30
- 1.7 Command Modes 31
- 1.9 CLI Error Messages 33
- 1.11 Using CLI Help 34
- 1.12 Accessing the CLI 34
- Switching Commands 37
- 2. Switching Commands 38
- Switching Commands AT8404 100
- AT8404 Switching Commands 101
- Quality of Service Commands 175
- Chapter 1 175
- -mapping 176
- 3.1.3 classofservice trust 177
- 3.1.4 cos-queue min-bandwidth 177
- 3.1.13 show packet-memory 180
- 3.1.16 show protection-group 181
- Mode Global Config 183
- 3.3.1 class-map 184
- 3.3.1.1 no class-map 184
- 3.3.2 class-map rename 184
- 3.3.3 match ethertype 184
- 3.3.4 match any 185
- 3.3.5 match class-map 185
- 3.3.5.1 no match class-map 186
- 3.3.6 match cos 186
- 3.3.7 match secondary-cos 186
- 3.3.9 match dstip 187
- 3.3.10 match dstip6 187
- 3.3.11 match dstl4port 187
- 3.3.12 match ip dscp 187
- 3.3.13 match ip precedence 188
- 3.3.14 match ip tos 188
- 3.3.15 match protocol 189
- 3.3.17 match srcip 189
- 3.3.18 match srcip6 190
- 3.3.19 match srcl4port 190
- 3.3.20 match vlan 190
- 3.3.21 match secondary-vlan 190
- 3.4 DiffServ Policy Commands 191
- 3.4.4 redirect 192
- 3.4.5 conform-color 192
- 3.4.6 class 192
- 3.4.6.1 no class 193
- 3.4.7 mark cos 193
- 3.4.8 mark ip-precedence 193
- 3.4.9 police-simple 194
- 3.4.10 policy-map 194
- 3.4.10.1 no policy-map 194
- 3.5 DiffServ Service Commands 195
- 3.6 DiffServ Show Commands 196
- Mode Privileged EXEC 197
- <slot/port> in 199
- 3.6.7 show service-policy 200
- 3.7.4 mac access-group 203
- 3.7.4.1 no mac access-group 203
- 3.7.5 show mac access-lists 203
- 3.8.1 access-list 204
- 3.8.1.1 no access-list 205
- 3.8.2 ip access-list 205
- 3.8.2.1 no ip access-list 206
- 3.8.3 ip access-list rename 206
- 3.8.5 ip access-group 207
- 3.8.5.1 no ip access-group 207
- 3.8.6 acl-trapflags 207
- 3.8.6.1 no acl-trapflags 207
- 3.8.7 show acl-traptimer 208
- 3.8.8 acl-traptimer 208
- 3.8.8.1 no acl-traptimer 208
- 3.8.9 show ip access-lists 208
- 3.8.10 show access-lists 209
- 3.9.1 ipv6 access-list 209
- 3.9.1.1 no ipv6 access-list 210
- 3.9.2 ipv6 access-list rename 210
- 3.9.3 {deny 210
- 3.9.4 ipv6 traffic-filter 211
- 3.9.5 show ipv6 access-lists 211
- 3.10.1 auto-voip all 212
- 3.10.1.1 no auto-voip all 212
- 3.10.2 auto-voip 213
- 3.10.2.1 no auto-voip 213
- 3.10.3 show auto-voip 213
- Utility Commands 215
- 4. Utility Commands 216
- AT8404 Utility Commands 217
- Utility Commands AT8404 218
- Management Commands 277
- 5. Management Commands 278
- AT8404 Management Commands 279
- Management Commands AT8404 280
- Getting Help 329
- A. Getting Help 330
- AT8404 Getting Help 331
- FASTPATH log messages 334
- B. FASTPATH Log Messages 335
- AT8404 FASTPATH log messages 336
- FASTPATH log messages AT8404 337
- List of Commands 350
- C. List of Commands 351
- .......3 - 9 352
- List of Commands AT8404 353
- AT8404 List of Commands 354
Produits connexes et manuels pour Matériel Kontron AT8404 CLI
Matériel Kontron AT8050 Manuel d'utilisateur
(165 pages)
(165 pages)
Matériel Kontron AT8242 Manuel d'utilisateur
(109 pages)
(109 pages)
Matériel Kontron AT8060 Manuel d'utilisateur
(160 pages)
(160 pages)
Matériel Kontron KTQ67-FLEX Manuel d'utilisateur
(137 pages)
(137 pages)
Panasonic KX-TG9471 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Anrufbeantworter Panasonic KX-TG9471.
Wir stellen 1 PDF-Handbücher Panasonic KX-TG9471 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Commentaires sur ces manuels